Payment & Shipping Terms:
|Max Pressure:||> 200Psi||Type:||Digital|
|Product Name:||Real-time Truck And Trailer Tire Pressure Monitoring TPMS System||Sensor Lifespan:||More Than 5 Years|
|Tire Quantity:||6-18 Pcs||Pressure Range:||6-12 Bar|
|High Temperature:||85 Celsius Degree||Alarm:||Label Blinking, Digital Data And Sound Alarm|
|Sound Alarm:||Available To Be Turn Off||Monitoring Range:||Low Pressure, High Pressure, High Temperature, Leakage|
|Frequency:||433.92MHz||Display Data Cycle Time:||6 Seconds|
Real-time 6 to 18 Truck and Trailer Tire Pressure Monitoring TPMS System
The sensor collects the pressure and temperature data in the tire. And it sends data by radio frequency. The repeater can receive the pressure and temperature data sent by the sensor and forward the information to the receiver.
When the tire pressure or temperature is higher or lower than the preset alarm threshold, the receiver will automatically send the appropriate alarm to remind the user to pay attention to the tire status and timely treatment, in order to avoid a flat tire and damage the accident tire.
Display install on the front dashboard with embeded installation.
Sensor is banded on the wheel hub.
(1)Display Receiver Installation
Having a slot opening in the center console in the appropriate location according to the size of the receiver ; the receiver power cord and car power supply line corresponding connection; the embedded display into, so completely consistent with the stuck.
(2)Bandage Sensor Installation
a. The sensor should be installed close to the valve, which will be more convenient for the receiver and sensor pairing and checking after the tire is installed.
b. After the sensor has been installed to check the sensor is loose, be sure to tighten the screws on the cable tie.
c. As a result of installation causes leakage, and thus cause failure, the Company does not assume joint responsibility and direct responsibility.
(3) RP Repeater Installation
a.The installation position of intelligent repeater should be in the position of the relatively empty. It can’t be lower than the cross beam of car chassis nearest to ground, but must close to the trailer tire(as picture below)
b.If there is no suitable trailer in the middle of the installation position can also choose to against the side of the trailer.
c.There must be no metal surface surrounded by three sides around the repeater.
(1) Repeater power supply has two cores, the red power line connected to the truck often positive power supply(VCC), black power line connected to the GND, and with a fixed cable tie to prevent wear and tear short circuit
(2) Make sure that the input voltage is compatible with the repeater's voltage range and connect the power cord according to the marked positive and negative positions.
(3) Please connect a repeater to the vehicle at a normal open power position and connect a 2A water-proof fuse to ensure the safety of the circuit.
Receiver Icon definition
Data Factory Default Setting
|High pressure warning data||12 Bar|
|Low pressure warning data||6 Bar|
|High temperature warning data||85 ℃|
Product Technical Parameters
|1||Working Voltage||DC 12V~DC 32V|
|2||Working Current||<10 mA|
|3||RF Signal Receiving Sensitivity||<-105 dbm|
|4||Working Temperature||-40℃ ~ 85℃|
|5||RF Transmit Signal Modulation Method||FSK|
|6||Working Frequency||433.92 Hz±30KHZ|
|1||Working Voltage||DC 12V~DC 32V|
|2||Working Frequency||433.92 MHz±30KHZ|
|3||RF Transmit Signal Modulation Method||FSK|
|4||RF Signal Transmission Power||< 10 dbm|
|5||RF Signal Receiving Sensitivity||<-105 dbm|
|6||Working Temperature||-40℃ ~ 85℃|
|1||Sensor battery model no.||CR2450(550mAh)|
|2||Quiescent Current||less than 0.7uA|
|4||Storage Temperature||-40℃~125℃(store in normal temperature)|
|5||Transmission current||less than 10mA|
|6||Sensor battery lifespan||More than 5 years|
|7||RF Transmit Signal Modulation Method||FSK|
|8||Working Frequency||433.92 MHz±30KHZ|
Contact Person: Highdart